Index / 2LR50

2LR50

2LR50 — alkaline, 3 V, 17.1 x 33.4 mm. Not listed by Energizer. The closest it still lists: CR17345 is too tall to close, and runs the same 3 V.

What fits the compartment, and what does not

Fit answers whether it enters the compartment. Voltage answers whether the circuit will notice. A cell that fits is not always a safe substitute.

Nothing Energizer still lists is the same depth. The one option below shares the diameter and stands 34.5 mm against this cell's 33.4, and every one of them is deeper than this cell, so the question is not the contact but the cover: a deeper cell goes into the opening and stops the lid closing.

Also stamped 1200A, EN132A

Unlisted, and everything listed is deeper

Energizer no longer lists 2LR50 (also 1200A), and everything listed at this diameter is deeper: CR17345 stands 34.5 mm where this one stands 33.4. It will go into the opening and it will not let the cover close, so there is nothing here to shim or pack out.

What the chemistry changes

Everything above answers size and voltage. What it cannot answer is chemistry, and 1 other kind is in play here beside the alkaline this cell uses.

• Alkaline drops in voltage steadily as it empties, so a device calibrated for a flat discharge will drift as it goes.
• Lithium runs at 3 V, roughly double the nominal of the alkaline and silver classes. Of the 26 lithium cells here whose envelope the maker publishes, 3 share that envelope with an alkaline or silver cell.

Several cells in one can, and what that costs

This is not one cell. It is a stack sealed in one can, which is why the voltage is a multiple and the diameter is not. 2LR50 at 3 V is 2 cells of 1.5 V in series.

A series stack is only as good as its worst cell. One weak element takes the whole can down, and nothing on the outside shows which one it was. Published capacity 650 mAh for the whole stack, not per cell: capacity does not add in series, voltage does. 1 cell measures close enough to compare against it in the Energizer data this site reads, and 1 of it is still listed.

• The nearest is CR17345: it goes in and stands too tall and runs 3 V, same volts.
• Energizer files it for North America, which is where the part is sold rather than where the cell will work.
• Energizer no longer lists 2LR50 at all, so whatever goes into that compartment next will be a substitution rather than a replacement.

Drawn to scale

Every published figure

11 figures are published, and one is not: impedance. The row is absent rather than estimated. It reached shelves as EN132A.

2 rows in the table are not the maker's but ours: stored energy and energy per cubic centimeter. Everything else is reproduced without change.

What the datasheet does not say

Beyond size and voltage the sheet for 2LR50 is thin: 2 published figures below, and no impedance, no cutoff and no operating range at all. That silence is the maker's, not ours.

The part occupies 7.7 cubic centimeters and weighs 18 g. Capacity and voltage together put 1950 milliwatt-hours in that space. Energizer files it for North America.

Mass against volume

18 g filling 7.7 cubic centimeters. When the printing has worn off, a kitchen scale separates two cells of one envelope faster than a caliper does.

Where the part is filed

North America. That is a statement about the maker's distribution and not about where the cell works.

Is that a lot of energy?

Nothing else measured shares this shell, so the comparison has to go site-wide: 1950 milliwatt-hours in 7.7 cubic centimeters is 253 mWh per cc, denser than 31% of every cell measured here. Density is ours: the maker publishes capacity and volume and never divides one by the other.

A width the catalog keeps returning to

17.1 mm is a width this catalog keeps coming back to: 9 cylinders sit within half a millimeter of it, 2LR50 included.

1 of those one is still listed. Its 253 milliwatt-hours per cubic centimeter sit above 31 percent of everything here that publishes both a capacity and a volume. 3 of the 69 cylinders share its 3 V exactly.

• 3-315INNC — the next step down by volume: 7.6 cubic centimeters against this cell's 7.7.
• 3-315I — the next step up: 7.8 cubic centimeters, 101% of this one.
• 3LR50 — 16.8 x 49.9 mm, 4.5 V, alkaline.
• 3MR50 — 17 x 50 mm, 4.09 V, mercuric oxide.

The maker's own part numbers

2LR50 carries 2 names beyond the designation, and every one of them is a manufacturer part number: a catalog line, not a size and not a standard.

• 1200A — a manufacturer part number for 2LR50, not a standard designation.
• EN132A — a manufacturer part number for 2LR50, not a standard designation.

The cell that differs only in depth

The code says the size, so the cells that get confused with 2LR50 are the ones that keep its diameter and change its depth. 9 cells share this diameter at depths from 21.5 to 99.8 mm, and every one of them enters the same opening.

It stands 1 of 1 in this envelope by stored energy. On a scale the difference shows before it shows on a caliper: this one weighs 18 g.

• 3MR9 — same diameter, 21.5 mm tall against this cell's 33.4: 11.9 mm shallower, which neither designation carries.
• CR17345 — same diameter, 34.5 mm tall against this cell's 33.4: 1.1 mm deeper, which neither designation carries.
• 4LR52 — same diameter, 44.9 mm tall against this cell's 33.4: 11.5 mm deeper, which neither designation carries.
• MR50 — 16 mm across at 1.4 V against 17.1 mm here, 1.1 mm apart: loose in this holder.

What this page cannot tell you

3 of the 7 fields this site reads are empty for 2LR50: cutoff voltage, impedance and operating temperature. Everything computed from them is absent from this page rather than estimated.

The blanks are the same in all 1 record behind this designation, so they are the catalog's silence and not a merge losing a value. What is not missing is the envelope: 17.1 x 33.4 mm, published and checked against the designation itself.

• No cutoff voltage — so this page cannot tell you what the capacity figure was counted down to, without which the capacity is a number without a scale.
• No impedance — so this page cannot tell you whether the cell can drive a pulse, which is the whole question in a watch or a sensor.
• No operating temperature — so this page cannot tell you whether the maker claims anything at all below freezing.

Before you swap anything

Everything here is computed from published dimensions and nominal voltages. That answers whether a cell enters the compartment and whether the voltage matches on paper. It does not answer what your device does with the difference, and it cannot: a cell that fits can still be the wrong cell.

One more limit, and it is the biggest. This site reads a single manufacturer’s catalog. When a page says a designation is not listed, that means Energizer no longer offers a part under it — not that nobody makes the cell. Other makers may still sell it, and for common sizes they usually do.

A voltage difference is one relation between two cells, and this page prints it from the cell it is about — in every table on the page, including the one listing cells no longer made. A figure always belongs to the cell whose voltage is printed beside it: a cell that runs lower than this one carries a minus here, one that runs higher carries a plus, and two cells at the same nominal voltage carry zero. Meet the same pair on the other cell’s page and the sign is the other one, with the figure taken against that cell instead of this one; where the two run at the same voltage, both pages print zero. The class beside the figure is not read off that figure directly. It is decided on the gap itself, taken against the higher of the two nominal voltages, so one pair of cells gets one class whichever page you meet it on: counted from this side the boundary of the class that still runs falls at 20.0% below and 25.0% above, which is the same gap divided once by the larger nominal and once by the smaller. What genuinely differs between the two directions is the consequence, and the words carry it: a cell that runs low makes a calibrated instrument read below true, and a cell that runs high makes it read above.

3 things this site cannot see. Whether the contacts reach a shorter cell. Whether the device was calibrated for a chemistry that holds its voltage flat, which silver oxide does and alkaline does not. Whether the equipment tolerates the higher current a different chemistry can deliver. Rechargeable cells are never a drop-in for primary cells regardless of size.

Cells measured next to this one

Nothing in this data is this exact size, but the diameter is a well populated one: 9 cells run from 21.5 to 99.8 mm deep, and this cell is one point on that scale.

• 3MR9 — 16.8 x 21.5 mm, 4.5 V
• CR17345 — 17 x 34.5 mm, 3 V
• 4LR52 — 17.1 x 44.9 mm, 6 V
• 3LR50 — 16.8 x 49.9 mm, 4.5 V

Where these numbers come from

Dimensions, voltages, chemistries and capacities are published by the manufacturer and reproduced without change. Everything else on the page is ours, computed from those figures: whether one cell fits where another sat, how far apart their voltages are, stored energy and energy per cubic centimeter, the rank within a shell, and the check of the designation against the measured size.

Fit is decided within 0.3 mm on every axis, which is the order of a contact spring's travel. Voltage classes are decided by consequence, not by roundness, and they are decided on the gap between two nominal voltages taken against the higher of the two: 2.0% or less of it is the same working voltage, 6.0% starts to matter to a calibrated instrument, and past 20.0% it is a different class altogether. Measuring the gap against the higher figure is what makes the verdict the same from either cell’s page, while the printed percentage stays counted from the cell you are reading about. Cells with identical stored energy share a rank instead of being ordered arbitrarily.

Ranking uses capacity times nominal voltage, because capacity alone is not comparable across chemistries: 150 mAh at 3 V is twice the energy of 150 mAh at 1.5 V. Neighbors are chosen by measurement and never alphabetically, because two cells filed next to each other by name usually have nothing in common. A blank in any table means the maker publishes no figure, which is not the same as zero.

Source: Energizer technical data, retrieved 1 September 2026.

The record behind this page

Every figure on this page comes from one catalog record, number 805, and it is linked below. The sheet is the document the dimensions, voltage and capacity were read out of.

1. [1] Energizer catalog record 805, listed as EN132A, obsolete in the snapshot. Technical data sheet: en132a.pdf.

Every figure above is reproduced from those records without change; the comparisons are ours and are described on the method page. Snapshot: Energizer technical data, retrieved 1 September 2026.

Putting this on a forum or a repair page? The same answer without the site around it — fit, voltage, chemistry and the limits that go with them — is at /embed/2lr50/. It loads nothing from anywhere else. Paste this:

<iframe src="https://batterycross.com/embed/2lr50/" width="100%" height="520" loading="lazy" title="2LR50 replacements"></iframe>